ubuntu 中文默认字体的设置

我一直希望能够分别设置中文和英文的字体，但是一直都没成功。

之前一直是只设置喜欢的英文字体作为默认字体，但是中文的话就非常难看，现象是很多文字字体，大小都不一致。

仔细想想，它(我一直用gnome)字体显示的工作原理大致是有个字体列表，然后要显示一个字的时候就依次查找，直到找到一个能够显示的为止。比如如果我设的默认字体是个中文字体，那么英文字体一般就会跟着改变。但是现在默认字体是英文的，显示中文时自然找不到，于是它就从自己的默认列表里去找到了。

至于列表具体存放的位置，我找了找，是在/etc/fonts/conf.d里，相关的有两个文件， 40-generic.conf 和 65-nonlatin.conf, 根据/etc/fonts/conf.avail里的说明，这些配置文件是按编号顺序依次加载的，于是修改65-nonlatin.conf, 由于我想使用文鼎楷体，于是找到对应的, 并把它移到所在里的最前面，成为第一个。

之后重启X时没进去，卡住了，然后重启了一下问题解决。

现在爽眼多了。

Comments

Determine Perspective Lines With Off-page Vanishing Point

In perspective drawing, a vanishing point represents a group of parallel lines, in other words, a direction. For any point on the paper, if we want a line towards the same direction (in the 3d space), we simply draw a line through it and the vanishing point. But sometimes the vanishing point is too far away, such that it is outside the paper/canvas. In this example, we have a point P and two perspective lines L1 and L2. The vanishing point VP is naturally the intersection of L1 and L2. The task is to draw a line through P and VP, without having VP on the paper. I am aware of a few traditional solutions: 1. Use extra pieces of paper such that we can extend L1 and L2 until we see VP. 2. Draw everything in a smaller scale, such that we can see both P and VP on the paper. Draw the line and scale everything back. 3. Draw a perspective grid using the Brewer Method. #1 and #2 might be quite practical. #3 may not guarantee a solution, unless we can measure distances/p...

Chasing an IO Phantom

My home server has been weird since months ago, it just becomes unresponsive occassionally. It is annoying but it happens only rarely, so normally I'd just wait or reboot it. But weeks ago I decided to get to the bottom of it. What's Wrong My system set up is: Root: SSD, LUKS + LVM + Ext4 Data: HDD, LUKS + ZFS 16GB RAM + 1GB swap Rootless dockerd The system may become unresponsive, when the IO on HDD is persistantly high for a while. Also: Often kswapd0 has high CPU High IO on root fs (SSD) From dockerd and some containers RAM usage is high, swap usage is low It is very strange that IO on HDD can affect SSD. Note that when this happens, even stopping the IO on HDD does not always help. Usually restarting dockerd does not help, but rebooting helps. Investigation: Swap An obvious potential root cause is the swap. High CPU on kswapd0 usually means the free memory is low and the kernel is busy exchanging data between disk and swap. However, I tried the following steps, none of the...

Moving Items Along Bezier Curves with CSS Animation (Part 2: Time Warp)

This is a follow-up of my earlier article. I realized that there is another way of achieving the same effect. This article has lots of nice examples and explanations, the basic idea is to make very simple @keyframe rules, usually just a linear movement, then use timing function to distort the time, such that the motion path becomes the desired curve. I'd like to call it the "time warp" hack. Demo See the Pen Interactive cubic Bezier curve + CSS animation by Lu Wang ( @coolwanglu ) on CodePen . How does it work? Recall that a cubic Bezier curve is defined by this formula :

B (t) = (1 - t)^{3} P_{0} + 3 (1 - t)^{2} t P_{1} + 3 (1 - t) t^{2} P_{2} + t^{3} P_{3}, 0 \leq t \leq 1.

In the 2D case,

B (t)

has two coordinates,

x (t)

and

y (t)

. Define

x_{i}

to the be x coordinate of

P_{i}

, then we have:

x (t) = (1 - t)^{3} x_{0} + 3 (1 - t)^{2} t x_{1} + 3 (1 - t) t^{2} x_{2} + t^{3} x_{3}, 0 \leq t \leq 1.

So, for our animated element, we want to make sure that the x coordiante (i.e. the "left" CSS property) is \(...

WangLu's Notes

Search This Blog